Ref: S-Series

Slip Ring - End of Shaft - 4, 6, 8, 10 Circuit - 12000 rpm

  • End of shaft (axial) slip ring
  • Circuit number: 4, 6, 8, 10
  • Maximum Rotation speed: standard 12 000 RPM - option : up to 20.000 rpm
  • Wire termination to color coded solder terminals and/or quick disconnect circular connectors
  • Maximum Peak Noise: 0.1ohm
  • Lifetime: 100 million revolution
  • Operating Temperature Range: -40°C to 121°C
  • Sealed against dust & permanently lubricated
  • Stator diameter: 41.3mm
  • Amplifier TC and PJ available

Download the product sheet

?

4, 6, 8 or 10 circuit cost-effective slip ring - axial

Michigan Scientific’s S-Series Slip Ring Assemblies are utilized for a variety of applications requiring up to 10 circuit connections. They are designed to mount on the end of a rotating shaft and make electrical connection to strain gages, thermocouples, or other sensors that have been installed on rotating equipment. The slip ring brushes and rings are made of precious metals, which minimize noise and enable the assemblies to be used for low level instrumentation signals. In addition, a high grade stainless steel case provides protection from dust and other contaminants.

These S-Series models are available in 4, 6, 8, and 10 circuit slip ring assemblies. Connections are made through color coded solder terminals located on both the slip ring rotor and slip ring stator. Permanently lubricated bearings eliminate the need for routine cleaning and maintenance. The lightweight and compact design of these slip ring assemblies make them ideal for use in applications where space is limited.

Installation

The slip ring can be easily mounted to the end of the shaft with two screws. Sensor's wires can either be linked to the surface or to the inside of the shaft. In the second scenario, a wire groove shall be milled across the end of the shaft or adapter. Connections are made through color coded solder terminals located on the slip ring rotor and a connector on the slip ring stator. Redundant terminals are included to provide back-up connections.

No additional setup is required. The slip ring can be mounted and used in any application. Another great feature is the limited space it takes: 33mm.

Available models

  • Length: de 28 à 41 mm.
  • Wiring connections through soldering terminals. The stator can be equipped with a connector in option.

Standard

Model Circuits Max speed (rpm) Rotor diameter Length Weight Comment Drawing
S4 4 12.000 41,28mm 33mm 111g Drawing
S4CF 4 12.000 41,28mm 33mm 111g Brush lifter
S6 6 12.000 41,28mm 36mm 113g Drawing
S6/G 6 12.000 41,28mm 36mm 130g 1 embedded amplifier for SG
S6/TC3 6 12.000 41,28mm 28mm 75g 3 embedded amplifiers for Thermocouple
S6M 6 12.000 50,8 mm 36mm
S8 8 12.000 41,28mm 41mm 116g Drawing
S8/2Gx 8 12.000 41,28mm 41mm 150g 2 embedded amplifier for SG
S10 10 12.000 41,28mm 41mm 119g Drawing
S10M/V 10 12.000 51,8mm 41mm
S10/15K09/LHV 10 20.000 41,28mm 41mm 100g grooved rings - lubeoil holes Drawing
S10M/15K09/LHV 10 20.000 41,28mm 50,8 mm 100g grooved rings - lubeoil holes Drawing

Wheatherproof

Model Circuits Max speed (rpm) Rotor diameter Length Weight Comment
S10/15K/W 10 15.000 63.5mm 41mm 100g

Applications

  • Torque measurements transmission
  • Rear axle measurements
  • Vibration measurements
  • Acceleration measurements
  • Brake measurements
  • Gearbox rendering measurements
Series
S-Series
Mounting
End of shaft
Circuits
4, 6, 8, 10
Max rotation speed
12000 , 20000 rpm
Wheatherproof
non available
Encoder
no
Courant maximal par voie
500 mA
Rotor Diameter
41.28 mm
Diamètre stator
31.24 mm
Longueur
33 mm
Température de fonctionnement
-40 to 121 °C
Contacts rotor
Picots à souder
Contact Stator
Picots à souder

Dimensions

  • Amplifier to connect between the sensor and the slip ring allowing the optimization of the signal's quality
  • Weatherproof version for outdoor applications
  • Encoder version for information transmission
  • Custom stator connector
  • Longer lifetime option
  • High speed option
  • Customized for exterme vibration
  • Custom wiring (cable length, connectors)

  • Signal conditioning for strain gage

  • Signal conditioning for thermocouple

  • Amplifier Housings

  • Connector Brackets

  • Fender Bracket

  • Rotor Adapters

  • Wheel Adapter Plates

  • Wheel Mounting Hardware

Related products

collecteur tournant bout d'arbre short S Series

SHORT S-SERIES

Slip Ring – End of Shaft – Compact – 4 to 10 Circuits - 12000 rpm
collecteur tournant mesure

SR Series

Robust Slip ring Assembly - End of shaft - 6 to 36 circuits
collecteur tournant

B4-2, B6-2, B8-2

Slip Ring – Tubular – 4, 6 or 8 circuits – 50.8mm – 7000rpm
collecteur tournant tubulaire

B4-2/E60, B6-2/E60, B8-2/E60

Slip Ring - Tubular - 4, 6 or 8 Circuits - 60 PPR Encoder - Rotor 50.8mm
Phone +33 1 46 91 93 36 Contact Contact form Newsletter S'inscrire à la newsletter